Training Requirements (TOC)

Before each running period, you must attend a classroom version of Users Training for Collider or Users Training for Fixed Target Areas (AGS) or re-qualify each year by taking the challenge exam.  First time users must attend a classroom session.  Aside from addressing Collider specific or AGS specific training, these programs incorporate other BNL training courses.  For example, Users Training for Fixed Target Areas incorporates equivalency for ODH, Stop Work, Emergency Planning, High Radiation Module, General Employee Training and reciprocity for DOE Trained Radiation Worker I.

If additional training requirements are needed for specific individuals, then the C-A Experimental Safety Review Committee or the C-A Radiation Safety Committee will identify these training requirements during the experiment review process.  NOTE: Local experiment-specific training or work planning may be required for work at your experiment.  You must meet all training requirements set by your Experiment Spokesperson, which are in addition to the training requirements prescribed here.

Training requirements for Collider Experiment Shift Leaders goes beyond Users Training for Collider.  If you are not a Collider Experiment Shift Leader and you only work at the Collider experimental areas, then Users Training for Collider is the only training requirement you must fulfill with regard to experimental area access.  Again, please take note that there may be additional local training requirements in order to perform work on the experiment.

As opposed to Collider experimental areas, Users who access the AGS experimental areas require Radiation Worker I Training in addition to Users Training for Fixed Target Areas (AGS) in order to obtain unescorted access to the slow-beam and fast beam areas.  If you are currently qualified in Radiation Worker I Training at another institution, then Users Training for Fixed Target Areas (AGS) is, by mutual agreement with the Radiological Controls Division, all which is needed.  If you lack Radiation Worker 1 Training and wish to work at the AGS experimental areas, then you must take the BNL version of Radiation Worker 1 Training.

Typically, the 1.5-hour classroom program for Users Training for Collider starts six to eight weeks before the onset of the experimental running period.  The classroom program is given every Monday at 1:00 p.m. in the Snyder Seminar Room, Building 911-A.  If you have previously attended the classroom program, you may elect to take a challenge exam.  Contact the Training Office, x5800 to arrange for the challenge exam.

Users Training for Fixed Target Areas (AGS) is given on demand.  If you have previously attended the classroom program, you may elect to take a challenge exam.  Contact the Training Office, x5800 to arrange for the challenge exam or a classroom presentation.

Please note that personal-radiation dosimeters (TLDs) are not required for most Collider experiment Users at this time.  However, if you are a Collider Experiment Shift Leader, then you will need a TLD.  In order to be issued a TLD, Radiation Worker I Training is required every other year.  If you have already taken the classroom program, you may take a challenge exam to re-qualify. 

Please read the following synopsis of ESH requirements that apply to C-A experimental areas.  Every User is responsible for knowing and observing the requirements.

Reporting ESH Issues (TOC)

In C-A experimental areas, the potential exists for serious acci­dents.  There are latent hazards posed by heavy mechanical equipment, high-voltage high-current elec­trical systems, flammable gases, oxygen deficiency and radiation.  Although we have maintained an excellent ESH record in such a complex environment, the participation of each User who has access to experimental areas is necessary.  We want each User to be familiar with our ESH regulations and procedures.

If you observe any potential hazards or ESH problems, please report it to the Operations Coordinator in the C-A Main Control Room (x4662) as soon as possible or to the C-A ESHQ Division Head (x5272).

Users will find detailed written information on ESH requirements for reviewing experiments by linking to C-A procedure OPM 9.2.1.  The C-A Department requires Experiment Spokespersons to review their experiments against BNL requirements, which are located in the Subject Areas Section of the BNL Standards Based Management System (SBMS), and to receive formal approval for experiment startup. 

Your liaison physicist works directly with members of the C-A ESHQ Division, the C-A ESRC Chair and C-A RSC Chair to ensure the safe and environmentally sound operation of your experiment.  Your liaison physicist is your main contact person for ESH related issues.  A list of liaison physicists is located at: http://www.rhichome.bnl.gov/AGS/Accel/SND/Liaisons/liaisons.html. 

Your experiment also has a liaison engineer who coordinates the installation of large experimental components within the experimental hall and the interfaces with C-A utilities.  The liaison engineer works with Users, designers and the trades-people to meet BNL’s ESH design and installation requirements including work-planning requirements.

The Laboratory policy is to protect the health and safety of employees, Users and the public.  The C-A Department Chair and the C-A Associate Chair for ESHQ are responsible for the implementation of formal ESH programs at the C-A.  The C-A ESHQ Division Head carries out this program on a day-to-day basis.  However, it is important to recognize that you are responsible for your own safety, and that you will be held personally accountable if you do not follow C-A requirements.  We note that your liaison physicist is most familiar with C-A requirements.

Normal communications regarding ESH issues should go through your liaison physicist; e.g., shielding modifications, beam intensity changes, tours, visitor requirements and training. 

Injuries (TOC)

All injuries that occur at the Laboratory of such severity as to require first aid or a physician's treatment should be reported to the BNL Occu­pational Health Clinic (x3670).  If a medical emergency occurs while working in the experimental areas, then also notify the Main Control Room (C-A Main Control Room, x4662).  Emergency medical assistance is always available by calling x911.

Equipment Hazards (TOC)

Any potential hazards associated with experimental equipment problems should be reported to the on-duty Operations Coordinator (x4662) and your liaison physicist as soon as possible.

Visitors and Minors (TOC)

The Experiment Spokesperson is responsible for all personnel visiting your experiment.  A fully trained C-A User must accompany visitors.  The Head or the ESHQ Division and the liaison physicist must be notified of any tours you arrange for groups of visitors.

Individuals under 18 years of age are not permitted in the experimental areas without the permission of the C-A Chair, C-A Associate Chair for ESHQ or C-A ESHQ Division Head.

ESH Reviews (TOC)

Your liaison physicist must be notified beforehand about all materials, chemicals or equipment that you bring into the C-A.  Each experiment or modification to the experiment must undergo a review for conventional ESH issues by the C-A Experi­mental Safety Review Committee (Y. Makdisi, Chair, x4932).  Procedures for reviewing conventional safety aspects of experiments are given in C-A OPM 9.2.1.  Sufficient drawings and certifications must be made available for review of equipment that is fabricated at a non-BNL facility.  The C-A Radiation Safety Committee (D. Beavis, Chair, x7124) may also review the experiment for access controls and radiation protection issues if significant changes to the experimental area or beam are required.  Procedures for reviewing radiation safety aspects of experiments are give in C-A OPM 09.1.15.

Certain types of equipment, such as pressure vessels, vacuum vessels, cryostats and gas handling systems must not be operated before undergoing a thorough ESH review.  Your liaison physicist must be informed before the introduction of a potential hazard into the experimental areas so that a determination of the need for an ESH review can be made.  Sufficient time must be allowed for modifications to be accomplished before operation of the equipment.

Radiation Safety (TOC) 

GOLDEN RULES FOR RADIOLOGICAL AREAS AT C-A 

1. DO NOT climb over or defeat barriers  

2. DO NOT ignore radiological signs, labels, alarms, warnings or posted entry requirements especially a posted requirement to wear a TLD

Radiation safety requirements for specific experiments have been established and posted for each exper­imental area.  Please be sure to read the posted rules and follow them.

TLD badges may be required in certain experimental areas.  If the area is posted as a “Radiation Area” or posted as "Controlled Area TLD Required," then you must have RadWorker I Training, Users Training for Fixed Target Areas (AGS) and a TLD badge to enter.  These additional requirements will be clearly indicated on the sign.  You may also be escorted and you may wear a visitor TLD in a “Radiation Area” or “Controlled Area TLD Required.”

If the area is posted as "Controlled Area," such as at the Collider experiments, then you must have Users Training for Collider, but RadWorker I Training and a TLD are not required.  However, you need RadWorker I Training and Users Training for Collider for any work in or unescorted access into the RHIC tunnel.

Do not linger in radiological areas if you are not assigned to work in radiological areas.

Area radiation monitors, commonly called "chipmunks," are provided in experimental areas.  Please DO NOT MOVE OR TAMPER WITH THESE MONITORS.

Fetal radiation dose is subject to special radiation limits.  Declared pregnant C-A Users are subject to special restric­tions on total radiation exposure while working at the C-A.  Please in­form the Facility Support Representative, C. Schaefer (x4728), so that your work locations can be evaluated.

All radioactive sources must be reviewed and surveyed by a C-A ESHQ Radiological Control Technician (x4660) in order to check that the source does not leak.  If you are bringing a source to the C-A, contact the C-A Health Physics Office (x4660) before the source arrives, even if you are bringing it from another BNL Department or Building.  Offsite sources must always be shipped to and from C-A Department via the BNL Isotopes and Special Materials Group (x5233). 

Please be aware that it is our policy that no eating or drinking is permitted in Radiation Areas. 

Access Control Rules (TOC)

Do not climb fences or barriers.  YOU MUST ENTER YOUR EXPERIMENTAL AREA THROUGH A GATE AT ALL TIMES.  This will ensure beam is safely off.  Failure to follow this rule will result in your being denied access to the BNL site.

Do not remove, deface or otherwise alter a radiological barrier.

Obey all posted requirements.  Do not enter areas that are posted as High Radiation Areas or Contamination Areas.  Training beyond that of User Training and Radiation Worker I Training is required to enter these areas.

Follow all instructions on orange-colored Security System tags that are found on "chipmunks," certain power supplies, and other equipment that is interfaced with the access control system.

Fire Safety (TOC)

Smoking is not allowed in any C-A building.

Learn the location of the fire alarm pull-box for your area.  In case of fire or any other emergency call x911 or pull the fire alarm and then notify the Main Control Room (x4662).  All telephones have a location label.

Learn the local emergency procedures for your experiment, if any.  Certain experiments have formal emergency procedures.  Consult with your liaison physicist or Experiment Spokesperson.

The C-A complex must be evacuated immediately when you hear a pulsating siren and/or hear the continuous or intermittent ringing of fire alarm bells.  Once out of the building, personnel should remain clear of the C-A experimental buildings.  A public announcement will be made when it is safe to re-enter the experimental area.

Evacuation routes inside the experimental areas are sometimes compli­cated.  Be sure that you know your way quickly out of the building.  Please help to keep exit ways free of obstructions.

Do not place yourself at risk by attempting to fight a fire only with a portable extinguisher.  Call the Fire Department (x911) and Main Control Room (x4662) first, and then use the extinguisher.

Automatic fire extinguishing systems are installed in some experimental areas.  If you are present when a system discharges, condensation in the room or enclosure may cloud the area and it is advisable to leave the area once the system has discharged.  The gases are, however, not a danger to your health.  Discharge time is normally 10 seconds or less.

Experimental equipment using flammable gases or liquids requires an ESH review before operation.  It is important to be aware of the additional C-A Department requirements established for this type equipment.

Combustible materials, such as paper, cardboard boxes, wooden material, etc., should not be allowed to accumulate in experimental areas.

Cryogenic Fluids (TOC)

Do not smoke or create ignition sources near hydrogen or deuterium reservoirs, dewars, transfer lines or other equipment containing flammable cryogenic fluids.

Exercise extreme caution if it is necessary to work in the immediate vicinity of a liquid H2 target or vessel.

Cryogenic fluids can cause serious burns if spilled on tissue.  For handling cryogenic liquids, small or large volume:

Cryogenic fluid spills can create oxygen deficient atmospheres.  Obey all cryogenic alarms and leave the area if a spill is occurs.  Do not travel though the vapor cloud since the extremely cold air may harm lung tissue.

Work Planning (TOC)

Users are required to file work plans before beginning work at C-A facilities.  The procedure for Work Control for Experimenters, OPM 2.29, provides the details for preparing a list of pre-approved Low-Hazard tasks.  This list is prepared and posted by the Experiment Spokesperson, or his/her designate, and the C-A Work Control Manager.  Users who perform tasks not included on the list should contact the liaison physicist or liaison engineer to determine if additional ESH review of the task is warranted. 

Performance of Moderate or High-Hazard tasks must meet the requirements in BNL Standard 1.3.6 for Work Planning, which entails obtaining an authorization using BNL’s “Green Work-Permit.”  Working on flammable gas systems, working at heights or work around large vacuum windows may fall in the Moderate or High Hazard categories, and your liaison engineer or liaison physicist should be contacted to assist in the initial stages of work planning.

Certain experimental collaborations have additional work planning requirements, and may even have experimental "work coordinators."  Experiments may have procedures for specific tasks, and some procedures may be under C-A configuration control.  Check Chapter 11 of the C-A OPM for experiment specific procedures.  Consult with your liaison physicist or Experiment Spokesperson regarding local work planning rules before starting a task in the experimental area.

Electrical Safety Rules (TOC)

In addition to the hazards of contact with energized electrical circuits, the short-circuit capacity of the 120/208 and 480-volt systems is much above that encountered at most industrial and/or research facilities.  Connection and disconnection to a C-A power distribution system that requires tools must be made only by qualified BNL personnel.  Please be cautious when working on equipment that has been connected to the 120/208 and 480-volt systems, a short circuit can produce a large arc, with a resultant molten metal spray.

Do not work on electrical equipment that is energized with 1) greater than 50 V ac rms, 2) greater than 50 V dc, 3) greater than 10 ma of available current or 4) greater than 10 joules of energy.  Contact the C-A Training and Procedures Manager (x7146) to complete additional electrical safety training requirements before beginning electrical work of this nature.

The red hold tag is used for protection of person­nel, and the equipment to which it is attached should never be operated.  Only the person who attached the tag may remove it.  In the event this person is not available, a special review process can be initiated by C-A Main Control (x4662).

Magnetic Field Safety (TOC) 

Use extreme caution with iron and steel objects when working around mag­nets, especially those magnets with large gaps.  Be sure you do not inadver­tently energize a magnet before the area is clear.  Remember that the field may be effective at a surprisingly long distance.

Obey warning signs regarding pacemakers, and respect local magnetic safety plans and barriers, if any.  It is required that persons with implants or cardiac devices have a physical prior to work in posted magnetic field areas.  Please contact your liaison physicist to set up an appointment before entering posted magnetic field areas if you have such devices.

Large spectrometer magnets require an ESH review before initial turn­ on and following any modifications to adjacent apparatus or shielding.

Vacuum Windows (TOC)

Be sure a vacuum window shutter is in place when working around large vacuum windows.  Remember that an air hammer may cause significant equipment damage and personnel injury should you be a few feet from a failed window.

Laser Requirements (TOC)

All lasers in the experimental areas need to be reviewed by the BNL Laser ESH Officer, Chris Weilandics, x2593, before initial use or following modification to a previously reviewed laser.  Make sure that you are aware of the ESH requirements, including medical surveillance requirements, established for the laser(s) in your area.

Waste Rules and Pollution Prevention (TOC)

Each User is responsible to handle, accumulate or dispose of radioactive or hazardous waste using adequate controls and documentation, and appropriate training.  While your liaison physicist or liaison engineer may be knowledgeable in ESH rules, waste rules and waste-handling forms are complex, change frequently, and your waste may require special handling and labeling.  You must contact the C-A Environmental Coordinator (x7520) for assistance in removing all waste from C-A.

Minimize the amount of waste generated by: 1) substituting re-usable materials where possible, 2) irradiating minimum quantities of materials and 3) segregating different wastes to allow for reclamation. 

Do not put ordinary waste in Radioactive Waste cans.  This would increase the radioactive waste burden. 

Lists of pollution prevention techniques and products requiring recycling are located at https://sbms.bnl.gov/sbmsearch/subjarea/23/23_Exh2.cfm?ExhibitID=6316  

Stop-Work (TOC)

  <